Research Article 
Machining of Nickel Alloy 242 with Cubic Boron Nitride Tools
H.H. Habeeb, K. Kadirgama, M.M. Noor, M.M. Rahman, B. Mohammad, R.A. Bakar and K.A. Abouel Hossein
Journal of Applied Sciences, 2010, 10(19), 2322-2327.
Abstract
This study discusses the development of first and second order of surface roughness prediction model when machining Haynes 242 alloy with Cubic Boron Nitride (CBN) at dry condition. The relationship between the cutting parameters (cutting speed, axial depth and feedrate) with surface roughness are discussed. Response Surface Method (RSM) has been selected to optimize the cutting parameters and reduce the number of experiments. Surface roughness obtained in these experiments ranged from 0.052-0.08 μm, which consider as an extremely fine finish. Increase in cutting speed from 70 to 300 m min-1, the roughness getting finer. On other hand, increase in feedrate (0.1 to 0.3 mm tooth-1) and axial depth (0.025 to 0.075 mm) surface roughness become rougher.
ASCI-ID: 35-3641
Similar Articles
The Damage of the Cutting Tools out of Carbide Metallic During the Turning of a Soaked and not Hardened Steel XC38
Journal of Applied Sciences, 2010, 10(10), 813-822.
Tool Temperature and Cutting Forces during the Machining of Particleboard and Solid WoodJournal of Applied Sciences, 2010, 10(22), 2881-2886.
Multi-objective Optimisation of Machining Fibre Reinforced CompositesJournal of Applied Sciences, 2012, 12(23), 2360-2367.
The Wear Characteristics of Cemented Tungsten Carbide Tools in Machining Oil Palm Empty Fruit Bunch ParticleboardJournal of Applied Sciences, 2009, 9(18), 3397-3401.
Genetic Algorithms in Optimization and Computer Aided DesignJournal of Applied Sciences, 2001, 1(3), 289-294.
A Genetic Algorithm to Solve the Maximum Partition ProblemJournal of Applied Sciences, 2002, 2(1), 71-73.
The Economic-environmental Neural Network Model for Electrical Power DispatchingJournal of Applied Sciences, 2004, 4(3), 340-343.
Optimization of a Heavy Continuous Rolling Mill System Via SimulationJournal of Applied Sciences, 2006, 6(3), 611-615.
Sequential and Parallel Genetic Algorithms for the Hybrid Flow Shop Scheduling ProblemJournal of Applied Sciences, 2006, 6(4), 775-778.
An Algebraically Derived Minimal Cost Solution Technique of the EOQ Model Under Conditional Trade CreditJournal of Applied Sciences, 2006, 6(4), 750-754.
The Optimal Method of Nonlinear Decoding for Nonlinear Encoding of QAM SignalJournal of Applied Sciences, 2006, 6(10), 2292-2296.
The Influence of Process Parameters on Lactic Acid Fermentation in Laboratory Scale FermenterJournal of Applied Sciences, 2006, 6(10), 2287-2291.
Digital Circuit Structure Design via Evolutionary Algorithm MethodJournal of Applied Sciences, 2007, 7(3), 380-385.
Modelling of Magnetic Proprieties of FeNb Coatings Produced by HVOF Thermal SprayingJournal of Applied Sciences, 2007, 7(3), 386-391.
EPQ Models under Permissible Payment Delay: An Algebraic ApproachJournal of Applied Sciences, 2007, 7(4), 515-518.
Determining an Optimum Model for Production in Paper Industry: Case Study of Iranian Mazandaran Wood and Paper IndustriesJournal of Applied Sciences, 2007, 7(20), 3075-3080.
Carboxymethylation of Cassava Starch in Different Solvents and Solvent-Water Mixtures: Optimization of Reaction ConditionsJournal of Applied Sciences, 2008, 8(8), 1581-1585.
A Genetic Approach to Optimize Mathematical Model of Facilities Relocation Problem in Supply ChainJournal of Applied Sciences, 2008, 8(18), 3119-3128.
Multi-Objective Differential Evolution Algorithm for Solving Engineering ProblemsJournal of Applied Sciences, 2009, 9(20), 3652-3661.
A Solution for Time-Dependent Multimodal Shortest Path ProblemJournal of Applied Sciences, 2009, 9(21), 3804-3812.
Optimization of the Hardened Concrete Properties with GA and LPJournal of Applied Sciences, 2007, 7(24), 3918-3926.
Optimization of the Artificial Neural Networks UsingAnt Colony Algorithm to Predict the Variation of Stock Price IndexJournal of Applied Sciences, 2010, 10(3), 221-225.
A Novel Optimized Neural Network Model for Cost Estimation using Genetic AlgorithmJournal of Applied Sciences, 2010, 10(6), 512-516.
PFPSO: An Optimised Filtering Approach Based on SamplingJournal of Applied Sciences, 2010, 10(6), 494-499.
New Method for Finding an Optimal Solution to Quadratic Programming ProblemsJournal of Applied Sciences, 2010, 10(15), 1627-1631.
Response Surface Methodology Study on Removal of Humic Acid from Aqueous Solutions Using Anionic Clay HydrotalciteJournal of Applied Sciences, 2010, 10(19), 2297-2303.
Improved Evolving Kernel of Fisher’s Discriminant Analysis for Classification ProblemJournal of Applied Sciences, 2009, 9(12), 2313-2318.
Multiple Performance Optimization for the Best Metal Injection Molding Green CompactJournal of Applied Sciences, 2011, 11(9), 1663-1667.
Development of Artificial Neural Network for Optimisation of Reusability in Automotive ComponentsJournal of Applied Sciences, 2011, 11(6), 996-1003.
Optimization of Process Parameter Variability in 45 nm PMOS Device using Taguchi MethodJournal of Applied Sciences, 2011, 11(7), 1261-1266.
Response Surface Methodology Approach to Optimizing Process Variables for the Densification of Rice Straw as a Rural Alternative Solid FuelJournal of Applied Sciences, 2011, 11(7), 1192-1198.
Optimal Computerized Model for Designing Cellular Manufacturing Systems using Neural NetworkJournal of Applied Sciences, 2011, 11(15), 2837-2842.
Destabilization of Heavy and Light Crude Oil Emulsions via Microwave Heating Technology: An Optimization StudyJournal of Applied Sciences, 2011, 11(16), 2898-2906.
Slub Yarn Quality Optimization by using Desirability Function and Neural NetworksJournal of Applied Sciences, 2011, 11(17), 3204-3208.
Simulation Based Analysis of Erbium Doped Amplifier (EDFA)Journal of Applied Sciences, 2006, 6(4), 789-794.
Optimization by Grey Relational Analysis of EDM Parameters in Machining Al-15% SiC MMC Using Multihole ElectrodeJournal of Applied Sciences, 2012, 12(10), 963-970.
Optimization of Oxytetracycline Degradation Inside UV/H2O2 Reactor Using Box-Behnken Experimental DesignJournal of Applied Sciences, 2012, 12(11), 1154-1159.
Optimal Capacity and Placement of Wind Power Generation System Under Wind Speed Uncertainties: A ReviewJournal of Applied Sciences, 2012, 12(20), 2107-2114.
A Hybrid Simulated Annealing with Solutions Memory for Curriculum-based Course Timetabling ProblemJournal of Applied Sciences, 2013, 13(2), 262-269.
Optimization of Multilevel Image Thresholding Using the Bees AlgorithmJournal of Applied Sciences, 2013, 13(3), 458-464.
Optimization of Hybrid Solar and Wind Power GenerationJournal of Applied Sciences, 2013, 13(6), 869-875.
Evaluation and Optimization of Children's Recreational Center in Urban Green Public Space Based on AHP-TOPSISJournal of Applied Sciences, 2013, 13(6), 895-900.
A Review of Mathematical Model Describing Insulin Delivery System for Type 1 DiabetesJournal of Applied Sciences, 2014, 14(13), 1465-1468.
Dynamics Simulation and Optimization of Ride Comfort for Car on Random RoadJournal of Applied Sciences, 2013, 13(15), 3035-3041.
A Semi-Markov Process based Optimization Method for Availability of Hybrid Flow ShopJournal of Applied Sciences, 2013, 13(16), 3340-3344.
Coordination and Optimization of Supply Chain under a New Buy-back ContractJournal of Applied Sciences, 2013, 13(17), 3543-3547.
Study on the Delivery Area Optimization and ManagementJournal of Applied Sciences, 2013, 13(18), 3730-3735.
Optimization of Design Proposal of Community Environment Landscape based on ANP ModelJournal of Applied Sciences, 2013, 13(7), 1123-1127.
Economic Optimization Mathematical Model of the Public Building Canopy StructureJournal of Applied Sciences, 2013, 13(21), 4738-4743.
Development of a Sustainable Integrated Process Design and Control for Chemical ProcessesJournal of Applied Sciences, 2014, 14(12), 1277-1282.
Planning a Nutritious and Healthy Menu For Malaysian School Children Aged 13-18 Using "Delete-reshuffle Algorithm" in Binary Integer ProgrammingJournal of Applied Sciences, 2015, 15(10), 1239-1244.
A Deterministic Inventory Model under Quantity-depended Payments Delay Policy Using Algebraic MethodJournal of Applied Sciences, 2006, 6(2), 406-410.
Optimization of Reservoir Operation by Genetic Algorithm Considering Inflow Probabilities (Case Study: The Jiroft Dam Reservoir)Journal of Applied Sciences, 2008, 8(11), 2173-2177.
A New Algorithm for Optimum Design of Mechanical Draft Wet Cooling TowersJournal of Applied Sciences, 2009, 9(3), 561-566.
A Heuristic Traditional MIP Solving Approach for Long Term Production Scheduling in Open Pit MineJournal of Applied Sciences, 2008, 8(24), 4512-4522.
Intelligent System for Continuous Gas Lift Operation and Design with Unlimited Gas SupplyJournal of Applied Sciences, 2009, 9(10), 1889-1897.
A Two-Step Biodiesel Production from Waste Cooking Oil: Optimization of Pre-Treatment StepJournal of Applied Sciences, 2009, 9(17), 3098-3103.
Biodiesel Production from Crude Palm Oil by Transesterification ProcessJournal of Applied Sciences, 2009, 9(17), 3166-3170.
Optimization of a Novel Nitric Oxide Sensor Using a Latex Rubber MatrixJournal of Applied Sciences, 2007, 7(23), 3801-3805.
Neural Network for Farm Household Output PredictionJournal of Applied Sciences, 2016, 16(12), 594-599.
Optimization of Physical Conditions of Actinokinase Synthesis from Local Isolate Using Response Surface Methodology (RSM)Journal of Applied Sciences, 2020, 20(1), 35-43.
Fourth Order Torque Prediction Model in End MillingJournal of Applied Sciences, 2009, 9(13), 2431-2437.
A Study on Abrasive Water Jet Machining of Aluminum with Garnet AbrasivesJournal of Applied Sciences, 2005, 5(9), 1650-1654.
Surface Roughness Investigation in the Electrical Discharge Machining of Powder Metal MaterialJournal of Applied Sciences, 2007, 7(12), 1608-1613.
Effect of Wood Finishing and Planing on Surface Smoothness of Finished WoodJournal of Applied Sciences, 2007, 7(16), 2300-2306.
Designing, Building and Testing of an Electropolishing CellJournal of Applied Sciences, 2008, 8(10), 1912-1918.
Plasticity Analysis of Pure Aluminium Extruded with an RBD Palm Olein LubricantJournal of Applied Sciences, 2009, 9(19), 3581-3586.
Empirical Modeling of Surface Roughness in turning process of 1060 steel using Factorial Design MethodologyJournal of Applied Sciences, 2007, 7(17), 2509-2513.
Characterization of Areas of Pixels Modified During the Generation of Multiscale Digital Elevation ModelsJournal of Applied Sciences, 2007, 7(20), 3069-3074.
Workpiece Surface Temperature for In-process Surface Roughness Prediction using Response Surface MethodologyJournal of Applied Sciences, 2011, 11(2), 308-315.
The Effect of Tool Surface Roughness in Cold Work ExtrusionJournal of Applied Sciences, 2011, 11(2), 367-372.
Study on the Effect of Surface Finish on Corrosion of Carbon Steel in CO2 EnvironmentJournal of Applied Sciences, 2011, 11(11), 2053-2057.
Artificial Neural Network Modeling for Predicting Surface Roughness in End Milling of Al-SiCp Metal Matrix Composites and Its EvaluationJournal of Applied Sciences, 2012, 12(10), 955-962.
Performance of Silver Coated Copper Tool with Kerosene-servotherm Dielectric in EDM of Monel 400TMJournal of Applied Sciences, 2012, 12(10), 999-1005.
Surface Quality of Electro-discharge Machined Aluminum Metal Matrix CompositeJournal of Applied Sciences, 2012, 12(23), 2442-2447.
Effect of Cooling Environment on Grinding Performance of Nickel Based Superalloy Inconel 718Journal of Applied Sciences, 2012, 12(10), 947-954.
Computation of Surface Roughness of Mountains Extracted from Digital Elevation ModelsJournal of Applied Sciences, 2008, 8(2), 262-270.
Cited By
Energy Cost Modeling for High Speed Hard Turning
Journal of Applied Sciences, 2011, 11(14), 2578. DOI: 10.3923/jas.2011.2578.2584
State-of-the-art in surface integrity in machining of nickel-based super alloysInternational Journal of Machine Tools and Manufacture, 2016, 100(), 25. DOI: 10.1016/j.ijmachtools.2015.10.001
Sono-intercalation of CdS nanoparticles into the layers of titanate facilitates the sunlight degradation of Congo redJournal of Colloid and Interface Science, 2016, 462(), 130. DOI: 10.1016/j.jcis.2015.09.070
Design of liposomal formulations for cell targetingColloids and Surfaces B: Biointerfaces, 2015, 136(), 514. DOI: 10.1016/j.colsurfb.2015.09.034
Salt tolerance variability among stress-selected Panicum coloratum cv. Klein plantsGrass and Forage Science, 2015, (), n/a. DOI: 10.1111/gfs.12206
The in vitro effect of Lambda-cyhalothrin on quality and antioxidant responses of rainbow trout Oncorhynchus mykiss spermatozoaEnvironmental Toxicology and Pharmacology, 2015, 40(3), 855. DOI: 10.1016/j.etap.2015.09.018
Potential Protein Toxicity of Synthetic Pigments: Binding of Poncean S to Human Serum AlbuminBiophysical Journal, 2008, 94(3), 906. DOI: 10.1529/biophysj.107.120865
Utilization of starch films plasticized with urea as fertilizer for improvement of plant growthCarbohydrate Polymers, 2016, 137(), 127. DOI: 10.1016/j.carbpol.2015.10.051
Chitosan hydrogel beads impregnated with hexadecylamine for improved reactive blue 4 adsorptionCarbohydrate Polymers, 2016, 137(), 139. DOI: 10.1016/j.carbpol.2015.09.017
Coupling effects of water availability and pH on switchgrass and the optimization of these variables for switchgrass productivity determined by response surface methodologyBiomass and Bioenergy, 2015, 83(), 393. DOI: 10.1016/j.biombioe.2015.10.021
Application of PSX biocontrol preparation confers root-knot nematode management and increased fruit quality in tomato under field conditionsBiocontrol Science and Technology, 2016, 26(2), 174. DOI: 10.1080/09583157.2015.1085489
Effects of pupal treatment with Proteus® and Metarhizium anisopliae sensu lato on functional response of Habrobracon hebetor parasitising Helicoverpa armigera in an enclosed experiment systemBiocontrol Science and Technology, 2016, 26(2), 206. DOI: 10.1080/09583157.2015.1088933
Effect of the recent land use on the plant diversity and community structure of Omayed Biosphere Reserve, EgyptGlobal Ecology and Conservation, 2015, 4(), 26. DOI: 10.1016/j.gecco.2015.05.005
Interferometry as a tool for evaluating effects of antimicrobial doses on Mycobacterium bovis growthTuberculosis, 2015, (), . DOI: 10.1016/j.tube.2015.08.007
Physicochemical and functional properties of cowpea protein isolates treated with temperature or high hydrostatic pressureInnovative Food Science & Emerging Technologies, 2015, (), . DOI: 10.1016/j.ifset.2015.10.014
Automatic Path-Oriented Test Data Generation by Boundary HypercuboidsJournal of King Saud University - Computer and Information Sciences, 2015, (), . DOI: 10.1016/j.jksuci.2015.05.002
Compositional characteristics and energy potential of Chinese animal manure by type and as a wholeApplied Energy, 2015, 160(), 108. DOI: 10.1016/j.apenergy.2015.09.034
Cellulolytic and electrogenic activity of Enterobacter cloacae in mediatorless microbial fuel cellApplied Energy, 2015, 160(), 88. DOI: 10.1016/j.apenergy.2015.09.067
Mechanisms of resistance/tolerance of Pyrus communis to Stemphylium vesicarium. A transcriptome analysisAgroforestry Systems, 2015, 89(6), 991. DOI: 10.1007/s10457-015-9831-9
Torrefaction of Pinus radiata and Eucalyptus globulus: A combined experimental and modeling approach to process synthesisEnergy for Sustainable Development, 2015, 29(), 13. DOI: 10.1016/j.esd.2015.08.004
Experimental Study on Surface Roughness and Flank Wear in Turning of Nimonic C263 under Dry Cutting ConditionsJournal of Nanomaterials, 2021, 2021(), 1. DOI: 10.1155/2021/2054399